Tips From the Moving Company Pros: Ways To Move a Pinball Maker



With pinball making a substantial resurgence across the nation, Mild Giant wishes to ensure that these traditional, lovely machines stay damage-free while being transferred. Oh, and we desire individuals moving them to be safe, too.

Initially glimpse, pinball makers can appear intimidating to move because of their weight, fragility, and size. The good news is, our skilled Giants have a few techniques up their sleeves to guarantee your pinball is moved with ease.
Folding Down the Headbox

The bulk of modern pinballs (made in the last 20 years or two) have a hinge system which permits the headbox to be folded down. Early pinball makers had their headboxes bolted on, using either two or four bolts. All Electro-Mechanical pinballs utilize this system, in addition to the early Solid State machines.

Later devices have hinges and utilize a locking system to keep the headbox upright. There may also be two bolts inside as added security, in case the lock is broken or mistakenly un-latched.
Electro-Mechanical Pinballs

For Electro-Mechanical pinball machines, you need to eliminate the headbox rear gain access to panel to get to the bolts and plugs within. Usually this panel has a lock on it to keep it in place, but gradually the secret might have been lost. On a regular basis, there is a screw keeping this panel in place.

When inside, eliminate the bolts and disconnect the big connectors that have wiring going down into the device. You might wish to identify these adapters to put them back in the right spot, but they ought to be various sizes, making it tough to plug back improperly.

You can now get rid of the headbox entirely, or fold the headbox down onto the playfield glass. Make sure you use some foam, heavy cardboard, or blankets to protect the headbox from rubbing on the cabinet. Foam is best, as it will help keep the back glass in location.
Early Strong State Pinballs

For early Strong State Pinballs, you will require to get rid of the back glass. There is a lock located on the headbox in one of three locations: the left-hand side at the top, right-hand side at the top or on top of the headbox in the center.

As soon as opened, get rid of the back glass by lifting it up using the lift channel (at the bottom of the glass), and then pull it out from the bottom.

Then, open up the back box lamp panel by lifting the latch situated on either the left-hand side or right-hand side. The panel can now swing out to you, and offer you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs need you to lift up the lamp panel in order to swing it open.

Now that you are inside, you can remove the bolts, and any plugs that have wires going down into the machine. You may wish to label these plugs to put them back in the best area. You might not have to eliminate the plugs, as the circuitry needs to be long enough to permit the headbox to be folded down.

At this moment, you can secure the light panel and change the back glass.
Modern Strong State Pinballs

For Data East, Sega, and Stern Modern pinballs, there is a turnable latch system located at the back of the headbox. Using the supplied key, turn the latch 90 ° counter-clockwise.

For Williams, Bally, and Gottlieb, you can easily unlatch the back box at the back of the machine. This is a simple setup and requires no tools.

If you can now fold down the head box onto the cabinet, you're done. Make sure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will also help keep the back glass in place.

If you can not fold the head box down, then you have to get in. There is a lock located at the top of the back glass in the center. Use the supplied key to unlock, and eliminate the back glass by lifting it up from the bottom, and after that pulling it out from the bottom.

Next, you will need to eliminate the screen panel. You can do this by lifting it up and out. Open the lamp panel. There will be a latch located on either the right-hand or left-hand side. (Some newer Williams and Bally pinballs do not have a separate amp panel, it is part of the back glass panel. And later Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

Get rid of the 2 bolts, put the back box back together, and fold down the head box onto the cabinet. Make certain you utilize some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will likewise help keep the back glass in place.
Eliminating the Legs.

Pinball Maker legs are held in location by 8 bolts. The modern-day pinballs have captive nuts or threaded plates inside for the bolts to screw into.

However these threaded plates and captive nuts can be harmed, and using extra nuts may have been required. If this holds true, you will need to open up the front door of the pinball, slide out the playfield glass, and raise the playfield.

With the front door (coin door) open, move the lock down bar latch across and get rid of the lock down bar. Move out the playfield glass, and put in a safe location. Next, lift up the playfield by placing your hand where the ball drains, and lift the playfield up.

You should now have access to any nuts that might have been utilized. When any nuts have actually been eliminated, replace the playfield glass and lock down bar, and lock the front door.

Be sure to mark or remember which legs are for the front and back, as they will be changed in a different way to match.
Packing the Pinball.

You are now prepared to transfer your pinball machine. Before you fill it, make certain you get rid of the pinballs so they do not bounce around during transport.

If you are moving the moving specialty items pinball using a van or SUV, it may be much easier to get rid of the legs simply prior to loading the machine. Get a good friend to assist and have one of you supporting the pinball, while the other removes the front legs.

Make sure you strap the pinball in, as you do not desire it moving if you need to stop all of a sudden!

For Electro-Mechanical pinball machines, you need to get rid of the headbox rear gain access to panel to acquire access to the bolts and plugs inside. (Some more recent Williams and Bally pinballs do not have a different amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

If you are moving the pinball using a van or SUV, it might be much easier to eliminate the legs just prior to loading the maker. Get a buddy to help and have one of you supporting the pinball, while the other gets rid of the front legs.

Leave a Reply

Your email address will not be published. Required fields are marked *